Klarm Mould Blog

What Are The Purposes Of Hot Runner In Making Plastic Injection Molds?

12/14/201812/14/2018Klarm Mould

Basically, the injection molding process has been used the traditional way, which is known as the cold runner system. Nowadays, another method is getting popular. It’s known as the hot runner system. In this process, liquid substrate is put into the mold via a nozzle. So, the runner is kind of a passage through which the material travels. During the process, the substrate doesn’t cool down or get hard. Let’s find out why most people go for the hot runner for their plastic injection molds.

During a hot runner process, the mold is heated up and then cooled down once all of the cavity is full. Remember: the hot runner process may use many ways to heat up the injection mold, such as hot oil, hot water, induction/steam heating for quick heating. Unlike the cold runner system, this system cause fewer issues.

Now, let’s discuss why people go for the hot runner system in the injection molding process.

Less waste: This is an important point. In the hot runner system, the substance that passes through the chambers remains hot even when it reaches the last stage. In the cold molding, on the other hand, the runner is either discarded (waste) or recycled/reground. This is a disadvantage.

Quick cycle: As said earlier, the runner process requires time and may cause a loss of resource if enough time is not given. By fixing these problems, the hot runner system can boost the cycle times.

Keep in mind that the cooling and heating mold takes more time. Often, the time is offset through the savings from the elimination of the runner. However, it’s better to discuss the topic with your service provider.

Quality output: the removal of runners from the cold molded components requires a mechanical process. The product may get rejected if it is not up to the mark. In other words, the look and function of the product should be acceptable.

On the other hand, the hot molding can help resolve many issues, such as surface irregularities and burn marks, just to name a few.

Lower costs: cost is an importance consideration when opting for a cold or hot molding for a long-term. The initial cost of cold molding is less but the hot the hot runner system is a cost effective option as far as the long-term use is concerned.

Range of material: Actually, the inherent chemical composition of most of injection molding substance makes them a bit too “allergic” to temperature changes. The impact is stronger in extreme temperatures. So, for lower temperatures, the hot runner system is the way to go.

Colorant options: The hot runner system allows you to benefit from colorant mixtures in the process. So, this is another reason people opt for the hot runner process.

Long story short, these are the reasons the hot runner is an ideal choice for the majority of plastic injection mold projects. If you are looking to increase production in an efficient manner, we suggest that you give a go to this process. Hope this helps.

When it comes to hot runner injection mold, china plastic injection molding is the best choice.

Resource box: This article is originally posted in https://www.injectionmouldchina.com.

How to calculate production costs of making an injection mold

10/10/2018Klarm Mould

With the coming of the modern age, there have been a lot of new techniques that have been developed, but one can safely say that not all of them have been adopted by the industry. There are many reasons for it like they are not eco-friendly, or they can’t be easily automated, but the major reason that leads the way is they are not economically viable. There is no point in appointing a technique to produce something which is not worth the cost that one spent on creating it.

Injection molding is one such technique that has gained the attention of various industries and everyone is talking about it, but the same question still worries everyone, that what is the cost associated with it. In this article, we will try to describe how one can get a rough estimate of how much cost it will be on them once they start implementing the method.

Production rate: – One must have an idea about the product that they are going to make and how many cavities will be in there as it plays an important role in deciding the amount of material required which directly controls the total cost. Another thing that they need to aim for is the number of parts that will be produced in each cycle and the number of cycles in an hour. The larger the number of products produced in each cycle and the number of cycles in an hour, lower the cost of production.
The injection molding material used in each cycle: – It is not a good idea to simply measure the weight of the end product and then decide on how much material do you want. A substantial quantity of material is also scraped and wasted here and there and must be considered as well while calculating the material cost. An idea about the number of cavities that you will be having will also help with this
Other costs: – Other costs include the number of workers that you will be needing to carry out the different manual or automated operations. Workers doing manual work have low wages, but they will be needed in a large number while the workers working on the automated machine are skilled and will have a higher wage as compared to the workers doing manual work. Factors like the idle time of the different machines, post-processing time and the cost associated with giving final touches to the product must also be taken into consideration.

These are just some of the factors that go on deciding what the total cost will look like as they cover the core operations associated. Even the smallest of changes can go on to affect the total amount by a good amount and that’s why one should always aim to find the optimum method so as to balance all the cost involved resulting in the maximum profit that is the main goal.

Since China is the best place for any company to set up their factory, it is important to know about the China injection mold cost and on what factors does this amount depend on.

Resource box: This article is originally posted from https://www.injectionmouldchina.com.

What are the Worldwide standards of plastic injection molds?

08/23/201810/10/2018Klarm Mould

In the modern age, there are more and more upcoming manufacturing methods coming up that are allowing the industry to move in the forward direction at a great pace without compromising on the quality of the material being produced. Injection method is one such manufacturing process that has dynamically changed the whole industry and is being used by most of the major companies.

Injection molding method is the process of making or manufacturing any parts that are being required by injecting the molten material into a mold which is in the shape of the desired material. This technique is usually used with polymers and plastic, but can also be extended to different metals as well. Since this method is now being used by a large number of industries, there should be some standard that must be set at a global level so that the parts can be used all across the world without any tension of it malfunctioning or breaking down in between. There are specific technical specifications of the injection mold standards that need to be attained in order to make your product qualify as being usable. We will be discussing some of the most basic and elementary standards that need to be followed and one can look for a more detailed explanation on the internet afterwards.

Eco-Friendly: – the major reason to devise new techniques for everything these days is to save the environment and that goes for this technique as well. Polymers and plastics have long been ridiculed for their non-biodegradable nature and that’s why their usage has always been debated. Since this method aims to produce parts that will be used in the other industries, it is important to make sure that there is no major cause of pollution that will impact the environment in the long term as well as short term.
Durability: – Since the parts or the products made from injection molds will be used in the industries, they should be durable and long lasting. There is no point in manufacturing something that will break after only some days of use or will fall apart by the application of a small force.
Economical: – One of the major reasons people are trying to find more means and methods to use plastic components in an effective manner is that they are pretty cheap. The product that is being manufactured should be cheap in comparison with the other alternative products that are available in the market.
Automated: – Since we are dealing with molten materials, the automated process should be preferred because of many reasons. First of all is that it will largely reduce the accidents caused while handling molten materials, increase the work rate and save the cost of the workforce as well.

These are only some of the things that are standardized. There are a lot more things like the type of plastics that can be used, minimal smoothness that a product needs to have and many more. One should make sure that they comply with every rule so that they don’t face any difficulty in the near future.

China, having such a large workforce, is an ideal place for the companies to set up their factory and that’s why can find a large number of mold company China that are operating in the region successfully and have created a name for themselves.

Resource box: This article is originally posted from https://www.injectionmouldchina.com.

How to calculate injection molding cost

07/02/2018Klarm Mould

The question is a straightforward one, but there are various things to consider while calculating the cost. Factors like the durability of the mold, shipping cost, material selection, maintenance costs, etc. affects the final cost. The cost differs for every purchaser in different situations. You can go from the lowest to the highest depends on your choice and budget.

The durability of the mold – The injection mold you are choosing for should last for the entire program; if it loses its shape or characteristics then buying it will be just a waste of money. Also making a purchase from a trusted source is better to avoid future complications if the product turns out defective.

Shipping cost – It is a matter of concern for those who are buying mold on a foreign land. Getting it shipped to your workplace could be costly. It can cost a good share of the final price you pay for the product.

Maintenance cost – If you are making purchase offshore then its maintenance is your responsibility and getting it home with safety and looking after requires more money. If something misshapen during shipping then it may affect the product’s productivity. In such conditions, you will be obliged to make another purchase. And precaution is better than cure. It is better to invest a little more in its safety than buying altogether a new one.

Material selection – It is an important factor to keep in mind while selecting. Your payment rate depends upon the type of material you choose. The material should be strong enough to endure all the mechanical pressure it is about to go through.

Roughly the cost of the injection molding is the price finalized on the RFO but apart from this the cost of the mold also includes many factors that cannot be measured. That is the experience of the builder and what technique he is using. If the builder is good at his job and is experienced then work becomes easier and the cost of repeating the cycle again reduces bringing monetary savings. These things are not written on papers, but if you give it a thought then can cost you a good whooping amount. Plus there is always little wiggle room in the final cost of any product. It is better to keep a little sum aside for safety purposes. It will keep you ready in hard situations.

In case if you have already a fixed amount in your mind and don’t want to spend any extra buck then you should tell so to your mold builder. That way the mold will be designed with your instructions and budget in mind. If the number of cavities is higher in every per cycle then the parts will be less expensive allowing higher input. You can also opt for the basic products supplied by you rather than paying for it as part of the final product. Through these small hacks, you could save much money.

Need more insights on injection mold selection and costing then visit https://www.injectionmouldchina.com. They will not only provide you proper guidance but are also makers of best injecting mould in China. Here you will get all the details on China injection molding cost.

ISO 9001 Procedure for Making Automotive Injection Molds

06/22/2018Klarm Mould

The automotive industry is flourishing with the automotive injection molding at a considerable rate. The automotive injection molding gives the benefits of low costs and better consistency. The automotive injection molding had provided with high volume. The speed and the quality are the main aspects to focus on for the molders. A company which has proper ISO 9001 system is well-managed and the business performance is very good. The ISO 9001 is well recognized all over the world in the automotive business. The product is developed after taking reviews from the team to give the best to the customers.

What is ISO 9001?

The ISO 9001 ensures the quality of the products and the companies should maintain the quality of the ISO 9001 certification. There are many standards in the ISO 9000 group where only ISO 9001 is needed to be certified. For the certification, you need to fulfill the conditions in the sections. There are in total ten sections of the ISO 9001. The sections from four to ten cover the area of quality management. The sections include various things related to the business such as the process, standards of the product and risks in the production. The sections also take a look at the scope of the business and the investors. The revised plan of the company is required for the certification of the ISO 9001.

ISO 9001 Benefits and Goals

The companies are always in search of recognized molders for the supply of the products. With the ISO 9001, the employees should be trained in a specific process and they should be documented lawfully. Many automotive injection molds had processes which were not needed in the production and they were identified. The ISO 9001 standard is effective when there are disputes with the customers. The standard drives the molders to the growth and development of the molders. The software and spreadsheets have made it easy for the option of direct business. The companies with the standardized ISO 9001 certification are known to provide customer satisfaction than the companies who do not have the certification. They are also often observed to have higher profit margins in their businesses because of the constant improvements in the technology.

Risk Identification

The ISO 9001 focuses on the risks for the customers as well as for the molders towards reducing the risk factor. Some of the risks include the injuries to the workers which is taken care of very keenly, the standard focuses on the impacts that the business can cause to the environment. It also covers the factor that the employees should be well-trained for the job. The purchasing of the right raw material is important for the quality of the product which should be taken care of. The company has to ensure that everything is documented and this helps to identify some of the challenges for the company.

The automotive mold china maker is ISO 9001 standardized with high-quality products. The injection mold China company has been manufacturing various parts across the country as well as in the global market. China plastic injection molding is highly trusted by the customers.

The original source of this article is from https://www.injectionmouldchina.com.

THE IMPORTANCE OF MOLDING FLOW ANALYZE BEFORE MAKING INJECTION MOLDS

05/21/2018Klarm Mould

The injection mold is a method by which parts of an object is produced on large scale. Possibly the pen kept on the table near you is made through injection molding. Injection mold maker in China and countries expert in this technique have a good hold over manufacturing sector. There are many processes throughout the injection molding, which requires analyzing the cost, time and raw materials. One of the important pre-molding processes would be molding flow analysis.

Molding flow analysis helps to examine mold design thoroughly. It is pre-analysis of the product manufacturing process with the help of software. Molding flow tries to come to a pre-conclusion of the temperature required to melt the plastics or steel, of the amount required to fill in the cavity and deciding the wall thickness of the object. For example, if due to any reason the wall of the object is too thick it would not cool properly and there would be sink marks that will not look good.

Molding flow analysis is a pre-manufacturing process which not only reduces the cost, it saves the time of the organization and it helps to manufacture parts, objects in a successful way. Suppose without a flow analysis if a prototype is manufactured and it shows some fault, then it needs to be started all again. The design of the tool needs to be changed and there would be enormous wastage of time and energy. Therefore, to control all these mishappenings a molding flow analysis is done.

A company expert in this technique of mold, injection considers flow analysis a necessary pre-requisite. There are various manufacturing companies which are an expert in 3D designing of objects and they are also an expert in designing tool according to the desired wishes. That is why Southeast countries molds and supplies the parts in all over the world especially North America and Europe.

Now, coming again to the molding flow analysis, it examines the flow of melted metal or plastic through channels and tells the quantity to be added or to reduce before manufacturing the parts. It is easy to cut the metal scrap from the object, but it is very hard to add metals due to their characteristics into the parts. For that, a whole new design is carved for the tool which overruns the manufacturing cost and time. All these problems can be averted through proper mold flow analysis.

Injection molding is altogether an expert technique which requires technical knowledge and years of experience in the field. Southeast Asia is considered such an expert especially in plastic injection molds and it is aptly called as an injection molding hub. It supplies, parts being used in healthcare equipment, automotive, electronics and home appliances. Almost everything is being manufactured in countries of this region through injection molding.

Injection molding has made the process of manufacturing an easy task compared to earlier days where the heavy objects were manufactured in one go and where the technologies like flow analysis were not common. Injection molding has turned the pace of economy in a great way.

Original source is from https://www.injectionmouldchina.com, which is a professional plastic injection mold maker in China. China injection molding is considered to be the best in the world.

What Is A Quality Injection Mould Maker

03/28/201810/11/2018Klarm Mould

An injection mould maker is a machine for producing parts by injecting at high pressure, usually plastic material into a mould. The plastic used are thermoplastic and thermosetting polymers. Material for moulding is conveyed into a heated barrel where it is mixed and then injected into a mould cavity where it hardens by cooling into the shape of the mould. Mould may be made of steel, aluminium and are themselves made with extreme precision so that the desired parts are created to match the design. Vice versa, those parts are also designed so that they are well suited for injection moulding. The adaptability of injection moulding lies in this breadth of design consideration and possibilities, of both the injection mould maker in China and the item to be moulded.

Injection moulding finds application in almost all manufactured items, from plastic bottles to car parts.

A quality injection mould maker (person) should support his customer right from the concept stage to the mass production stage. He should know what questions to ask and anticipate where he is going to face difficulties in the moulding process while the part is being designed
A quality injection mould maker should be complete and integrated and yet have a variety of systems for different applications.
It would by virtue of being a quality item, be assisted by robotic systems.
They should be environmentally friendly, and have energy and space saving features.
The manufacturers should offer technical support and systems for factory automation.
Water circuits in a mould maker should not be looped as this leads to warpage.
The quality injection mould maker (person) should be present at the design stage of the part to anticipate difficulties in mould making and design.
Use of 3D rapid prototyping from 3D computer models is useful in injection moulding eg. To design water cooling channels along the contour of the mould which improves the quality of the parts and improves cycle times.
An internal storage memory for 50 molds is available
Fault diagnosis with alarm messages is possible
The command control centre should be shielded against magnetic interference.
A weekly schedule should be incorporated.
A quality injection mould maker that is driven by an electric motor has the following advantages over a hydraulic moulding machine

A significant energy reduction of 40% to 50% is possible by electric compared to a hydraulic injection mould
Stabilization of the molding process is achieved by use of the servo motor in the injection process
Noise generation level is much lower.
Molding cycle can be shortened by using different motors for different stages of the moulding cycle and running them in parallel, like opening, closing, injection, ejection, and weighing
Injection speed can be increased
Since no oil is used, it is an environmentally cleaner process.
A digital display is always welcome

They should be low maintenance
A two year warranty which covers the replacement and or repair of any part that has a manufacturing defect.

Injection mold makers in China are supplying plastic injection moulding machines all over the world, at very competitive rates. They are also setting up offices all over the world to serve their customers better.

Resource box: This article is originally posted from https://www.injectionmouldchina.com.